- Marvell Armada 37xx SoC pin and gpio controller
Each Armada 37xx SoC come with two pin and gpio controller one for the
south bridge and the other for the north bridge.
Inside this set of register the gpio latch allows exposing some
configuration of the SoC and especially the clock frequency of the
xtal. Hence, this node is a represent as syscon allowing sharing the
register between multiple hardware block.
GPIO and pin controller:
Main node:
Refer to pinctrl-bindings.txt in this directory for details of the
common pinctrl bindings used by client devices, including the meaning
of the phrase “pin configuration node”.
Required properties for pinctrl driver:
- compatible: “marvell,armada3710-sb-pinctrl”, “syscon, “simple-mfd”
for the south bridge "marvell,armada3710-nb-pinctrl", "syscon, "simple-mfd" for the north bridge - reg: The first set of register are for pinctrl/gpio and the second
set for the interrupt controller - interrupts: list of the interrupt use by the gpio
Available groups and functions for the North bridge:
group: jtag
- pins 20-24
- functions jtag, gpio
group sdio0
- pins 8-10
- functions sdio, gpio
group emmc_nb
- pins 27-35
- functions emmc, gpio
group pwm0
- pin 11 (GPIO1-11)
- functions pwm, gpio
group pwm1
- pin 12
- functions pwm, gpio
group pwm2
- pin 13
- functions pwm, gpio
group pwm3
- pin 14
- functions pwm, gpio
group pmic1
- pin 17
- functions pmic, gpio
group pmic0
- pin 16
- functions pmic, gpio
group i2c2
- pins 2-3
- functions i2c, gpio
group i2c1
- pins 0-1
- functions i2c, gpio
group spi_cs1
- pin 17
- functions spi, gpio
group spi_cs2
- pin 18
- functions spi, gpio
group spi_cs3
- pin 19
- functions spi, gpio
group onewire
- pin 4
- functions onewire, gpio
group uart1
- pins 25-26
- functions uart, gpio
group spi_quad
- pins 15-16
- functions spi, gpio
group uart2
- pins 9-10 and 18-19
- functions uart, gpio
Available groups and functions for the South bridge:
group usb32_drvvbus0
- pin 36
- functions drvbus, gpio
group usb2_drvvbus1
- pin 37
- functions drvbus, gpio
group sdio_sb
- pins 60-64
- functions sdio, gpio
group rgmii
- pins 42-55
- functions mii, gpio
group pcie1
- pins 39-40
- functions pcie, gpio
group ptp
- pins 56-58
- functions ptp, gpio
group ptp_clk
- pin 57
- functions ptp, mii
group ptp_trig
- pin 58
- functions ptp, mii
group mii_col
- pin 59
- functions mii, mii_err
GPIO subnode:
Please refer to gpio.txt in this directory for details of gpio-ranges property
and the common GPIO bindings used by client devices.
Required properties for gpio driver under the gpio subnode:
- interrupts: List of interrupt specifier for the controllers interrupt.
- gpio-controller: Marks the device node as a gpio controller.
- #gpio-cells: Should be 2. The first cell is the GPIO number and the
second cell specifies GPIO flags, as defined in
<dt-bindings/gpio/gpio.h>. Only the GPIO_ACTIVE_HIGH and
GPIO_ACTIVE_LOW flags are supported. - gpio-ranges: Range of pins managed by the GPIO controller.
Xtal Clock bindings for Marvell Armada 37xx SoCs
see Documentation/devicetree/bindings/clock/armada3700-xtal-clock.txt
Example:
pinctrl_sb: pinctrl-sb@18800 {
compatible = “marvell,armada3710-sb-pinctrl”, “syscon”, “simple-mfd”;
reg = <0x18800 0x100>, <0x18C00 0x20>;
gpio {
#gpio-cells = <2>;
gpio-ranges = <&pinctrl_sb 0 0 29>;
gpio-controller;
interrupts =
<GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>;
};
rgmii_pins: mii-pins {
groups = "rgmii";
function = "mii";
};
};
